Nimbra
Product Specifications
Home > Products and Services > Nimbra for broadcast grade reliability > Nimbra Product Specifications
| TECHNICAL SPECIFICATIONS | |||
| Base Unit: | Performance management: | ||
| Form factor | 3 RU height, 19 inch wide, 600 mm deep | ||
| Size | H: 134 mm, W: 444 mm, D: 570 mm | Type | ITU-T G.826 |
| Weight | Base Unit: 10.5 kg; Fully equipped: < 35 kg | Bins | 24h, 15min |
| Number of slots | 6 for Traffic Modules | Parameters | ES, SES, BBE, SS, UAS |
| 2 for combined Switch/NC Modules | Power consumption: | Max 1200W | |
| 2 for Power Modules | |||
| 1 AUX slot for sync and management | Environmental: | ||
| Switch capacity | 600 + 600 Gbps, non-blocking in redundant configuration | Operating temp: | 5 to 40°C (41 to 104°F) |
| (short term) | -5 to 55°C (23 to 131°F) | ||
| Power | 2×100-260VAC/1500W or 2×40-72VDC/2000W | Storage temp | -40 to 70°C (-40 to 156°F) |
| Fans | Two fan packs with 5 fans each, reversible airflow | Relative humidity | 10% to 90% (non-condensing) |
| Regulatory: | |||
| Plug-in unit 100G IP Trunk | Safety: | IEC62368 | |
| Standard | Eth, IEEE 802.3, IPv4 RFC 791, UDP RFC 768 | EMC | EN 300 386 (2014/108); FCC Part 15 Class A |
| Number of ports | 2 | CE marking | 768/2008/EC |
| Number of trunks | 32 | Environment | RoHS directive 2011/65/EU |
| Supported SFPs | 100GBASE-SR4/CWDM4/LR4/ER4 (QSFP28) | Ordering: | |
| Capacity | 100 Gbps bi-directional over backplane i/f | NPK0043-XW01 | Nimbra MSR 1060 Starter kit, redundant |
| 1 x Base Unit, 2 x SW1006, 2 x FAN1061 | |||
| Plug-in unit10G IP Trunk | NPQ0035-XW01 | Nimbra MSR 1060 Base unit, World wide | |
| Standard | Eth, IEEE 802.3, IPv4 RFC 791, UDP RFC 768 | NPS0083-1001 | SW1006 – Switch Module 600 + 600 Gbps |
| Number of ports | 20 | NPK0044-T001 | IF1020 – Trunk Module, 20x10G SFP+ |
| Supported SFPs | 10GBASE SR/LR/ER | NPK0045-T001 | IF1030 – Trunk Module, 2x100G QSFP28 |
| Number of trunks | 32 | NPM0041-MT1F | Additional Trunk feat lic |
| Capacity | 100 Gbps bi-directional over backplane i/f | NPA0135-PEX1 | PU1001-EX, 240/100VAC,1500/1200W, port exhaust |
| AUX Unit | |||
| NPA0135-PIN1 | PU1001-IN, 240/100VAC,1500/1200W, port intake | ||
| Synchronization | 4xHD-BNC, 1PPS in/out | ||
| 1.544/2.048/10 MHz in/out | NPA0136-PEX1 | PU1002-EX, 40-72VDC/2000W, port exhaust | |
| Mgmt/Console | 2 x RJ45, IP & Serial | NPA0136-PIN1 | PU1002-IN, 40-72VDC/2000W, port intake |
| Management: | SNMP v1/v2c/v3, Web element manager, CLI | NPA0138-0001 | Dummy SW-casette with fan controller (only when using single SW1006 module) |
| Maintenance: | Hardware hot-swap, Software remote download | ||
| NPA0131-0001 | FAN1061 – Fan pack type 1, reversible | ||
| TECHNICAL SPECIFICATIONS | |||
| Mechanical | Maintenance: | Hardware hot-swap, Software remote download | |
| Form factor | Plug-in unit for Nimbra MSR 1060, uses 1 slot | Power | |
| Size | H: 40 mm, W: 170 mm, D: 290 mm | Input | Internal -54 VDC x 2 |
| Weight | 1.8 kg | Consumption | Max 140 W |
| Lock/Release | Hand levers with locking latch | Environmental: | |
| IF1030 / IF1032 | Operating temp: | 5 to 40°C (41 to 104°F) | |
| 100 GbE | (short term) | -5 to 55°C (23 to 131°F) | |
| Standards | Ethernet, IEEE 802.3, IPv4 RFC 791, UDP RFC 768 | Storage temp | -40 to 70°C (-40 to 156°F) |
| Relative humidity | 10% to 90% (non-condensing) | ||
| Number of ports | 2 x QSFP28 (IF1030), 2 x QSFP28/CFP2 Combo (IF1032) | ||
| Regulatory: | |||
| Number of trunks | 32 | Safety: | IEC62368 |
| Supported SFPs | IF1030:100GBASE-SR4/LR4/ER4lite (QSFP28), IF1032: As IF1030 + ER4 and DCO (CFP2) | EMC | EN 300 386 (2014/108); FCC Part 15 Class A |
| CE marking | 768/2008/EC | ||
| Mapping | DPP-IP/UDP/IP/Ethernet, ~ 94.3 Gbps payload capacity | Environment | RoHS directive 2011/65/EU |
| Ordering: | |||
| BW Granularity | 4.096 Mbps | NPK0044-T001 | IF1020 – Media Acceleration Module,Trunk,10 G |
| Capacity | 100 Gbps to/from switch | NPK0045-T001 | IF1030 – Media Acceleration Module,Trunk,100 G |
| IF1020 10 GbE | NPK0047-T001 | IF1032 – Media Acceleration Module, Trunk, 100 GbE, Combo | |
| Standards | Ethernet, IEEE 802.3, IPv4 RFC 791, UDP, RFC 768 | ||
| NPM0041-MT1F | Additional Trunk feat lic | ||
| Number of ports | 20 | NPA0077-SRD1 | SFP+ Module 10GBASE-SR |
| Number of trunks | 32 | NPA0077-LRD1 | SFP+ Module 10GBASE-LR |
| Supported SFPs | 10GBASE SR/LR/ER | NPA0077-ER01 | SFP+ Module 10GBASE-ER |
| Mapping | DPP-IP/UDP/IP/Ethernet | NPA0077-ZR01 | SFP+ Module 10GBASE-ZR 80 km |
| ~ 9.43 Gbps payload capacity | NPA0144-SR40 | QSFP28, 100GBASE-SR4, 100m, 850nm, MMF, MPO, DDM | |
| BW Granularity | 4.096 Mbps | NPA0144-LR40 | QSFP28, 100GBASE-LR4, 10km, 1310nm band, SMF, DDM |
| Capacity | 100 Gbps to/from switch | NPA0144-ER40 | QSFP28, 100GBASE-ER4, 40km, 1310nm band, SMF, DDM |
| PM | NPA0144-CW40 | QSFP28, 100GBASE-CWDM4, 2km, 1310nm band, SMF, DDM | |
| Type | ITU-T G.826 | NPA0150-ER40 | CFP2, 100GBASE-ER4, 40km, 1310nm band, SMF, DDM |
| NPA0150-C101 | CFP2-DCO, 100 GbE Coherent, 80 km, OIF/MSA | ||
| Bins | 24h, 15min | ||
| Parameters | ES, SES, BBE, SS, UAS | ||
| Management: | SNMP v1/v2c/v3, Web element manager, CLI | ||
| TECHNICAL SPECIFICATIONS | |||
| Dimensions: | 445mm(17.5’’) x 445mm(17.5’’) x 240mm(9.4’’) | Environmental conditions: | |
| (HxWxD): | 19” and ETSI 300 119 compatible | Operating Temp: | 5 to 40°C (41 to 104°F) |
| Number of slots: | 16 for traffic boards, 2 for control modules, | (short term): | -5 to 55°C (23 to 131°F) |
| 2 for switch planes, 1 for alarm+aux interfaces, | Storage Temp: | -40 to 70°C (-40 to 156°F) | |
| 2 for redundant power modules | Relative humidity: | 10% to 90% (non-condensing) | |
| Switch Capacity: | 160 + 160 Gbps (unicast), 90 + 90 Gbps (multi-cast) in redundant configuration | Power: | |
| Voltage: | -48VDC nominal, -38 to -70V | ||
| Interface Modules: | OC-192/STM-64 Trunk | Dissipation: | <1200 W fully equipped |
| 4 x OC-48/STM-16 Trunk | Regulatory compliance: | ||
| 4 x OC-12/STM-4 Trunk | Safety: | UL60950-1 EN60950-1 | |
| 4 x OC-3/STM-1 Trunk | Laser Safety: | CFR 21 1040.10/11 | |
| 10 GE Trunk | EMC | FCC 15 Class A EN 300 386 | |
| 6 x IP/Ethernet Trunk | CE marking | 93/68/EE | |
| 8 x Gigabit Ethernet Access | |||
| 8 x Video Access | |||
| 8 x SFP Video Access | Management: | ||
| 8 x 3 Gbps Video Access | Element Mgmt: | Command Line Interface (CLI) | |
| JPEG2000 Video Access | Web GUI | ||
| 8 x AES/EBU Access | Network Mgmt: | Nimbra VisionTM | |
| Synchronization: | 3rd party NMS over SNMP v1/v2c/v3 | ||
| Input: | 2.048/1.544 MHz, sinus or square wave, | Maintenance: | Hot-swap |
| G.703.13 | Remote software and firmware download | ||
| Output: | 2.048 MHz, sinus, G.703.13 | Ordering Information: | |
| Software: | NPQ0012-XW01 | Nimbra MSR 688 Base Unit | |
| Basic SW: | NimOS | NPK0006-XW08 | Nimbra MSR 688 Starter Kit 80G, redundant |
| Element Manager | NPK0006-XW16 | Nimbra MSR 688 Starter Kit 160G, redundant | |
| SW options: | Dynamic Routing | NPS0032-6861 | Switch Module 80 Gbps, 8/16-slot |
| Ethernet Multicast | NPS0033-6001 | Switch Module 160 Gbs, 16-slot | |
| Native Video MulticastHD-SDI Support | NPS0034-6001 | Node Control Module, N602 | |
| SDI Frame Store | NPA0039-3001 | PCU -48 VDC / 30 A for Nimbra MSR 688 | |
| Ethernet Switching | |||
| TECHNICAL SPECIFICATIONS | |||
| Dimensions: | 267mm (10.5’’) x 445mm (17.5’’) x 240mm (9.4’’) | Environmental conditions: | |
| (HxWxD): | ETSI 300 119 compatible | Operating Temp: | 5 to 40 °C (41 to 104°F) |
| (short term): | -5 to 55 °C (23 to 131 °F) | ||
| Number of slots: | 8 for traffic boards, 2 for control modules, | Storage Temp: | -40 to 70 °C (-40 to 156 °F) |
| 2 for switch planes, 1 for alarm+aux interfaces, | Relative humidity | 10% to 90% (non-condensing) | |
| 2 for redundant power modules | |||
| Switch Capacity: | 80 + 80 Gbps (unicast), 45 + 45 Gbps (multicast) in redundant configuration | Power: | |
| Voltage: | 115/230VAC or -48VDC | ||
| Interface Modules: | OC-192/STM-64 Trunk | Dissipation: | <480w fully equipped |
| 4 x OC-48/STM-16 Trunk | |||
| 4 x OC-12/STM-4 Trunk | Regulatory compliance: | ||
| 4 x OC-3/STM-1 Trunk | Safety: | UL60950-1 | |
| 10 GE Trunk | EN60950-1 | ||
| 6 x IP/Ethernet Trunk | Laser safety: | CFR 21 1040.10/11 | |
| 8 x Gigabit Ethernet Access | EMC | FCC 15 Class A | |
| 8 x Video Access | EN 300 386 | ||
| 8 x 3 Gbps Video Access | CE marking | 93/68/EE | |
| JPEG2000 Video Access | |||
| 8 x ASI/AES Access | Management: | ||
| Synchronization: | Element Mgmt: | Command Line Interface (CLI) | |
| Input: | 2.048 or 1.544 MHz, G.703.13 | Web GUI | |
| Output: | 2.048 MHz, G.703.13 | Network Mgmt: | Nimbra VisionTM |
| 3rd party NMS over SNMP v1/v2c/v3 | |||
| Software: | Maintenance: | Hot-swap (all modules) | |
| Basic SW: | NimOS | Remote software and firmware download | |
| Element Manager | |||
| SW options: | Dynamic Routing | Ordering Information: | |
| Ethernet Multicast | NPQ0009-XW01 | Nimbra MSR 680 Base Unit | |
| Native Video Multicast | NPK0004-XW01 | Nimbra MSR 680 Starter Kit | |
| HD-SDI support | NPK0002-XW01 | Nimbra MSR 680 Starter Kit, redundant | |
| Ethernet Switching | NPS0032-6861 | Switch Module 80 Gbps, 8/16-slot | |
| SDI Frame Store | NPS0034-6001 | Node Control Module, N602 | |
| NPA0036-6001 | PSU 100-260 VAC/600W for Nimbra MSR 680 | ||
| NPA0039-1501 | PCU -48 VDC / 15 A for Nimbra MSR 680 | ||
| TECHNICAL SPECIFICATIONS | |||
| Dimensions: | 110mm(4.3’’) x 445mm(17.5’’) x 335mm(13.2’’) | Regulatory compliance: | |
| (HxWxD), incl. power supplies. | Safety: | UL60950-1 | |
| Capacity: | EN60950-1 | ||
| Switching: | 40Gbps in + 40Gbps out, non-blocking, single configuration | Laser safety: | CFR 21 1040.10/11 |
| EMC: | FCC 15 Class A EN 300 386 | ||
| Number of slots: | 4 | CE marking: | 93/68/EE |
| Interface: | Video: BNC, 75 ohm, configurable for direction and video format (optical interfaces available) | ||
| Ordering Information: | |||
| IP: 1000BASE-SX | NPQ0023-XW01 | Nimbra MSR 640 Base unit | |
| Formats: | SMPTE 2022-6, SMPTE 2110-10/20/30/40, | NPK0020-VJ02 | Nimbra MSR 640 Video Access (IP) (incl. J2K Video Access & IP uplink) |
| 3G-SDI, HD-SDI, SD-SDI, DVB-ASI | |||
| NPK0020-VJS1 | Nimbra MSR 640 Video Access (STM-1) (incl. J2K Video Access & OC-3/STM-1 uplink) | ||
| JPEG2000: | ISO/IEC 15444-1 | ||
| Capacity: | Max compressed bitrate 1000 Mbps | NPK0020-VJS4 | Nimbra MSR 640 Video Access (STM-4) (incl. J2K Video Access & OC-12/STM-4 uplink) |
| Formats: | SD-SDI: 10 – 125 Mbps (max 4 streams) | ||
| HD-SDI: 10 – 250 Mbps (max 4 streams) | NPK0020-VJS6 | Nimbra MSR 640 Video Access (STM-16) (incl. J2K Video Access & OC-48/STM-16 up-link) | |
| 3G-SDI: 10 – 500 Mbps (max 2 streams) | |||
| Interface, Ethernet: | Small form factor pluggable (SFP) | NPK0020-VS01 | Nimbra MSR 640 SFP Video Access (IP) (incl. SFP J2K Video Access & IP uplink) |
| Laser options: | 1000BASE-SX, 1000BASE-LX, 1000BASE-ZX, | ||
| 1000Base-T | NPK0020-VSS1 | Nimbra MSR 640 SFP Video Access (STM-1) (incl. SFP J2K Video Access & OC-3/STM-1 uplink) | |
| Standards: | IEEE 802.1Q, IEEE 802.1p. RFC2474, IEEE | ||
| 802.1D-2004 | |||
| NPK0020-VSS4 | Nimbra MSR 640 SFP Video Access (STM-4) (incl. SFP J2K Video Access & OC-12/STM-4 uplink) | ||
| Management: | SNMP (v1/v2c/v3), Web GUI, Nimbra Vision | ||
| Maintenance: | Hardware hot-swap | NPK0020-VSS6 | Nimbra MSR 640 SFP Video Access (STM-16) (incl. SFP J2K Video Access & OC-48/STM-16 uplink) |
| Remote software and firmware download | |||
| Environmental Conditions: | NPA0099-6401 | Nimbra MSR 640 AC Power Supply Unit | |
| Operating Temp: | 5 to 40°C (41 to 104°F) | NPA0101-6412 | Nimbra MSR 640 DC Power Conditioning Unit |
| (short term): | -5 to 55°C (23 to 131°F) | ||
| Storage Temp: | -40 to 70°C (-40 to 156°F) | Software options: | |
| Relative Humid: | 10% to 90% (non-condensing) | NPM0036-10FI | 10GE interface option Feature License |
| NPM0041-MT6F | Additional Trunk Feature License | ||
| Power: | NPM0037-64VF | Video Port Feature License | |
| Voltage: | 100/260VAC or -48VDC | NPM0031-6H1F | J2K Processing Feature License |
| Dissipation: | <400w fully equipped | NPM0035-EH6F | Hitless 1+1 Feature License |
| NPM0021-6FSF | Frame Synchronizer Feature License | ||
| TECHNICAL SPECIFICATIONS | |||
| Video Formats | |||
| SD | 625i (25), 525i (29.97) SMPTE 259M, SMPTE 305M | Frame Synchronizer | |
| Reference input | Digital 3G/HD/SD-SDI, analog bi- and tri-level sync | ||
| HD | 1080i (50/59.94/60) 1080p (23.98/24/25/29.97/30) 1080psf (23.98/24/25/29.97/30) 720p (23.98/24/25/29.97/30/50/59.94/60) SMPTE 292M, SMPTE 348M IP SMPTE ST-2022/6 | Alignment mode | – Single channel alignment to external sync ref. – 4K UHD quad-SDI alignment – Remote production multi-feed alignment |
| Encapsulation | MXF and VSF TR-01 | ||
| 3G (FHD) | 1080p (50/59.94/60) SMPTE 424M IP SMPTE ST-2022/6 | ||
| Protection | FEC (SMPTE2022-1), | ||
| Hitless 1+1 protection (SMPTE2022-7) | |||
| 4K (UHD) | 2160p, Quad HD/3G-SDI and 2SI | Delay offset | |
| Video Encoding | Ordering | ||
| Compression | JPEG2000, ISO/IEC 15444-1 | NPM0065-JPM1 | JPEG2000 Media Function |
| Sampling | 4:2:2, 10-bit | NPM0031-6H1F | J2K Processing Feature License |
| Nr. of channels | 16 (SD/HD), 8 (FHD), 2 (UHD), individually configurable for video format and encoding/decoding | NPM0021-6FSF | Frame Synchronizer Feature License |
| NPM0048-4KF1 | 4K Feature license | ||
| NPM0035-EH6F | Hitless 1+1 Feature License | ||
| Encoding bitrate | 10-125 Mbps (SD), 10-500 Mbps (HD), | ||
| 10-500 Mbps (FHD), 40-2000 Mbps (UHD) | NPS0088-6001 | IF628 – Media Acceleration Module | |
| Audio & ANC data | |||
| Embedded Audio | 16 channels, 20/24bit, user selectable, SMPTE299, SMPTE272M, SMPTE436M | ||
| Ancillary data | VBI: full transparent transport of user selectable lines ANC: AFD, ANSI/SCTE 104 Messages, ATC Ancillary Timecode, Caption Distribution Pack-et, CEA-608 Data, OP-47 SDP, OP-47 VANC multipacket, VPID, WSS. User selectable. | ||
| Form factor | Plug-in unit for Nimbra MSR 600 series, 1 slot | Environmental: | |
| Operating temp: | 5 to 40°C (41 to 104°F) | ||
| Interface | (short term) | -5 to 55°C (23 to 131°F) | |
| Connector type | SFP, SFP+, Video SFP, emSFP | Storage temp | -40 to 70°C (-40 to 156°F) |
| Interface type | Ethernet: 1G/10GBASE SR/LR/ER Video: SMPTE 297-2006, emSFP | Relative humidity | 10% to 90% (non-condensing) |
| Number of ports | SFP+: 8 ports, Video SFP: 16 ports configurable as input or output per SFP cage | ||
| Regulatory Compliance | |||
| Sync | Safety: | UL60950, EN60950 | |
| Connector type | HD BNC, 75 Ohm | EMC | FCC 15 Class A, EN 300 386 |
| Number of ports | 2 (1 In + 1 out) | CE marking | 93/68/EE |
| Environment | RoHS directive 2002/95/EC | ||
| Maintenance | Hardware hot-swap, remote software upgrade | ||
| Ordering: | |||
| Power Consumption | <60w | NPS0088-6001 | IF628 – Media Acceleration Module |
| TECHNICAL SPECIFICATIONS | |||
| Form factor | Plug-in unit for Nimbra MSR 600 series, 1 slot | Environmental: | |
| Operating temp: | 5 to 40°C (41 to 104°F) | ||
| Interfaces | (short term) | -5 to 55°C (23 to 131°F) | |
| Network | 2x SFP+ 1G/10GBASE SR/LR/ER | Storage temp | -40 to 70°C (-40 to 156°F) |
| 2x RJ45 10/100/1000BASE-T | Relative humidity | 10% to 90% (non-condensing) | |
| Aux | 1x RJ45 10/100/1000BASE-T | ||
| CPU | Intel Xeon, D-1528 1,9Ghz | Regulatory Compliance | |
| RAM | 8 GB, DDR4L-2133 | Safety: | UL60950, EN60950 |
| Storage | 32 GB mSATA SSD | EMC | FCC 15 Class A, EN 300 386 |
| Operating System | Linux Ubuntu 14 | CE marking | 93/68/EE |
| Environment | RoHS directive 2002/95/EC | ||
| Maintenance | Hardware hot-swap, remote software upgrade | ||
| Ordering: | |||
| Power consumption | <65w | NPS0080-6001 | IF630 – Media Processing Module |
| TECHNICAL SPECIFICATIONS | |
| Form factor: | |
| Plug-in unit for Nimbra MSR 600 Series switches, 1 interface slot | Management: |
| Interface, common: | SNMP: v1/v2c/v3 |
| Ports: 8 x SFP, configurable 3G/HD/SD-SDI or ASI, In/Out/Monitor | Element Manager: Web GUI, CLI |
| Return loss: >10 dB @ 3G, >15 dB @ HD, > 20 dB @ SD | |
| Maintenance: | |
| Interface, 3G SDI: | Hardware: Hot-swap |
| Standard: SMPTE 424M 3 Gbps SDI | Firmware: Remote download |
| Frequency: 2.97 or 2.97/1.001 Gbps | |
| Environmental Conditions: | |
| Interface, HD SDI: | Operating Temp: 5 to 40°C (41 to 104°F) |
| Standard: SMPTE 292M HD-SDI, SMPTE 348M HD-SDT, SMPTE 297-2006I | (short term): -5 to 55°C (23 to 131°F) |
| Frequency: 1.485 or 1.485/1.001 Gbps | Storage Temp: -40 to 70°C (-40 to 156°F) |
| Relative Humid: 10% to 90% (non-condensing) | |
| Interface, SD SDI: | |
| Standard: SMPTE 259M SD-SDI, SMPTE 305M SD-SDTI, SMPTE 297-2006 | Regulatory Compliance: |
| Frequency: 270 Mbps | Safety: UL60950 |
| EN60950 | |
| Interface, ASI: | EMC: FCC 15 Class A |
| Standard: DVB-ASI, CENELEC EN 50083-9 | EN 300 386 |
| Frequency: 270 Mbps | CE marking: 93/68/EE |
| Environment: RoHS directive 2002/95/EC | |
| Interface, SMPTE 2022 IP: | |
| Standard: SMPTE 2022-6 | Ordering Information: |
| NPS0054-6F01 IF624 – SFP Video Access Module J2K | |
| JPEG2000: | NPM0037-64VF Video Port Feature License |
| Standard: ISO/IEC 15444-1 | NPM0031-6H1F J2K Processing Feature License |
| Capacity: Sum of compressed streams < 1000 Mbps | NPM0021-6FSF Frame Synchronizer Feature License |
| Ranges: SD-SDI: 10 – 50 Mbps (max 4 streams) | NPM0048-4KF1 4K Feature license (incl NPM0021-6FSF) |
| HD-SDI: 10 – 250 Mbps (max 4 streams) | NPM0035-EH6F Hitless 1+1 Feature License |
| 3G-SDI: 10 – 500 Mbps (max 2 streams) | |
| Performance management: | SFPs are ordered separately. See Video SFP data sheet. |
| ITU-T G.826 based | |
| Bins: 24h, 15min | |
| Parameters: ES, SES, BBE, UAS |
| TECHNICAL SPECIFICATIONS | |||
| Form factor: | Plug-in unit for Nimbra MSR 600 series, uses 1 slot Selectable 5 or 10 Gbps backplane allocation. | Maintenance: | |
| Hardware: | Hot swap | ||
| Firmware: | Remote upgrade | ||
| Interface options: | |||
| Small Form-factor Pluggable (SFP+) | 1G/10GBASE SR/LR/ER | Power consumption: <50w | |
| Management: | |||
| Number of ports: | 2 ports | SNMP: | v1/v2c/v3 |
| Element Manager: | Web GUI, CLI | ||
| Mapping: | Network Manager: | Nimbra Vision | |
| DTM: | ETSI ES 201 803-11 | ||
| Environmental conditions: | |||
| QoS channelization: | ETS (Ethernet Transport Service) according to ETSI ES 201 803-7, supporting up to 119 ETS channels per board. | Operating temp: | 5 to 40 oC (41 to 104 oF) |
| ETS Channel cap: | n x 512 kbps ( n = 1 to 19512) | (short term): | -5 to 55 oC (23 to 131 oF) |
| Storage temp: | -40 to 70oC (-40 to 156 oF) | ||
| Relative humid: | 10% to 90% (non-condensing) | ||
| Supported standards: | |||
| IEEE 802.1Q | Virtual LANs | Regulatory compliance: | |
| IEEE 802.1D-1998 | Ethernet Precedence | Safety: | IEC/EN 60950-1 |
| RFC2474 | Diffserv Precedence | CE marking: | 93/68/EEC |
| IEEE 802.1D-2004 | MAC Bridges* | EMC: | ETSI EN 300 386 |
| * NPM0020-600F feature license required | FCC: | Part 15 sub-part B | |
| Laser safety: | CFR 21 1040.10/11 | ||
| Frame storage: | Environmental: | RoHS directive 2002/95/EC | |
| Packet memory: | 128 MB | ||
| Max frame size: | 9208 B (jumbo frames) | Ordering information: | |
| NPK0029-01FA | IF625 – Access Module, 1/10GE | ||
| Fault management: | NPA0077-SRD1 | SFP+ Module 1G/10GBASE-SR | |
| Communication/Equipment alarms | NPA0077-LRD1 | SFP+ Module 1G/10GBASE-LR | |
| Defects: | LOS, RBR, AIS, DEG | NPA0077-ER01 | SFP+ Module 10GBASE-ER |
| NPM0020-600F | Ethernet Switching feature license | ||
| Performance management: | NPM0035-EH6F | Hitless 1+1 feature license, Nimbra MSR 600 | |
| ITU-T G.826 based | NPM0036-10FI | 10GE interface option feature license | |
| Bins: | 24h, 15min | ||
| Parameters: | ES, SES, BBE, UAS | ||
| TECHNICAL SPECIFICATIONS | |||
| Form factor: | Plug-in unit for Nimbra MSR 600 series, uses 1 slot | Maintenance: | |
| Selectable 5 or 10 Gbps backplane allocation. | Hardware: | Hot swap | |
| Firmware: | Remote upgrade | ||
| Interface options: | |||
| Small Form-factor | 1000BASE-SX (MM, 850 nm, 550 m) | Power consumption: | <50w |
| Pluggable (SFP) | 1000BASE-LX (SM, 1310 nm, 10 km) | ||
| 1000BASE-ZX (SM, 1550 nm, 70 km) | Management: | ||
| 1000Base-T (UTP, Cat 5, 100m) | SNMP: | v1/v2c/v3 | |
| Mapping: | Element Manager: | Web GUI, CLI | |
| DTM: | ETSI ES 201 803-11 | Network Manager: | Nimbra Vision |
| QoS channelization: ETS (Ethernet Transport Service) according to | |||
| ETSI ES 201 803-7, supporting up to 248 ETS | Environmental conditions: | ||
| channels per board. | Operating temp: | 5 to 40 oC (41 to 104 oF) | |
| ETS Channel cap: | n x 512 kbps ( n = 1 to 19512) | (short term): | -5 to 55 oC (23 to 131 oF) |
| Storage temp: | -40 to 70oC (-40 to 156 oF) | ||
| Supported standards: | Relative humid: | 10% to 90% (non-condensing) | |
| IEEE 802.1Q | Virtual LANs | ||
| IEEE 802.1D-1998 | Ethernet Precedence | Regulatory compliance: | |
| RFC2474 | Diffserv Precedence | Safety: | IEC/EN 60950-1 |
| IEEE 802.1D-2004 | MAC Bridges* | CE marking: | 93/68/EEC |
| EMC: | ETSI EN 300 386 | ||
| * NPM0020-6001 feature license required | FCC: | Part 15 sub-part B | |
| Laser safety: | CFR 21 1040.10/11 | ||
| Frame storage: | Environmental: | RoHS directive 2002/95/EC | |
| Packet memory: | 128 MB | ||
| Max frame size: | 9208 B (jumbo frames) | Ordering information: | |
| NPS0043-6001 | 8 x Gigabit Ethernet Access Module | ||
| Fault management: | NPA0012-S011 | SFP Module GbE-SX (500m) | |
| Communication/Equipment alarms | NPA0012-L101 | SFP Module GbE-LX (10 km) | |
| Defects: | LOS, RBR, AIS, DEG | NPA0012-V701 | SFP Module GbE-ZX (70km) |
| NPA0040-T001 | SFP Module GbE-T (100m) | ||
| Performance management: | NPM0020-6001 | Ethernet Switching Feature License for Nimbra MSR 600 | |
| ITU-T G.826 based | NPM0035-ESH6 | Hitless ETS 1+1 Protection Switching Feature License for Nimbra MSR 600 | |
| Bins: | 24h, 15min | NPM0035-ESH3 | Hitless ETS 1+1 Protection Switching Feature License for Nimbra MSR 300 |
| Parameters: | ES, SES, BBE, UAS | ||
| TECHNICAL SPECIFICATIONS | |||
| Form factor: | Plug-in unit for Nimbra MSR 600 Series switches, 1 interface slot | Jitter: | |
| AES Out intrinsic: | < 0.025 UI pp @ 48 kHz | ||
| AES Input tolerance: 0.25 UI @ >8kHz | |||
| Interface: | ASI PCR | < ± 150 ns (no PCR re-stamping) | |
| Ports: | 8 x BNC, 75 ohm, configurable In/Out/Monitor | ||
| Performance management: | |||
| Interface, ASI: | ITU-T G.826 based | ||
| Standard: | DVB-ASI, CENELEC EN 50083-9 | Bins: | 24h, 15min |
| Frequency: | 270 Mbps | Parameters: | ES, SES, BBE, UAS |
| Input freq. tolerance: ± 100 ppm | |||
| Output frequency: | ± 20 ppm | Management: | |
| Return loss: | >20 dB (27-270 MHz) | SNMP: | v1/v2c/v3 |
| Signal amplitude: | 800 mV ± 10% | Element Manager: | Web GUI, CLI |
| DC offset: | +0.5 to –0.5 V | ||
| Rise and fall times: | (20%-80%) max 1.2 ns | Maintenance: | |
| Reach: | 275 m (900 feet), Belden 1694A | Hardware: | Hot-swap |
| Firmware: | Remote download | ||
| Interface, AES: | |||
| Standards: | AES3/5/11-2003, AES-3id-2001 | Environmental Conditions: | |
| Sample rates: | 32/48/96/192/44.1/88.2/176.4 kHz | Operating Temp: | 5 to 40°C (41 to 104°F) |
| Input freq. tolerance: ± 10 ppm | (short term): | -5 to 55°C (23 to 131°F) | |
| Return loss: | >20 dB | Storage Temp: | -40 to 70°C (-40 to 156°F) |
| Reach: | 330 m (1000 feet), Belden 1694A | Relative Humid: | 10% to 90% (non-condensing) |
| Interface, MADI: | Regulatory Compliance: | ||
| Standards: | AES10-2008 | Safety: | UL60950 |
| Sample rates: | 32/48/96/44.1/88.2 kHz | EN60950 | |
| Input freq. tolerance: ± 100 ppm | EMC: | FCC 15 Class A | |
| Return loss: | >20 dB (5 – 62.5 MHz) | EN 300 386 | |
| Reach: | 330 m (1000 feet), Belden 1694A | CE marking: | 93/68/EE |
| Environment: | RoHS directive 2002/95/EC | ||
| Mapping: | |||
| Transport: | DTM (ETSI ES 201 803) | Ordering Information: | |
| ASI TS bandwidth: | 2 – 212 Mbps | NPS0042-6001 | 8 x ASI/AES Access Module |
| NPM0032-ASI1 | ASI FW option for 8 x ASI/AES Access Module | ||
| NPM0032-AES1 | AES FW option for 8 x ASI/AES Access Module | ||
| NPM0033-6001 | MADI Feature license | ||
| TECHNICAL SPECIFICATIONS | |||
| Form factor: | Plug-in unit for Nimbra MSR 680/688, uses 1 slot | Network & Fault Management: | |
| Alarms: | Communication and Equipment | ||
| Physical Interface: | SNMP: | v1/v2c/v3 | |
| Interface type: | SFP/SFP+ ports | Element Manager: | Web GUI, CLI |
| Number of ports: | 2 | Network Manager: | Nimbra Vision |
| Supported SFPs: | 10GBASE SR/LR/ER, 1000BASE-T/SX/LX/ZX | ||
| Port speed: | 10, 100, 1000 Mbps and 10 Gbps | Timing and Synchronization: | |
| Modes: | Network timing Hold-over/Local External reference | ||
| Mapping: | |||
| Encapsulation: | DTM over DPP-IP/UDP/IP/Ethernet | ||
| FEC: | 2-20 columns, 4-20 rows, rows x columns <= 100 | ||
| BW granularity: | 0.512 Mbps | Environmental conditions: | |
| Backplane modes: | 10 Gbps or 5 Gbps | Operating temp: | 5 to 40 oC (41 to 104 oF) |
| Transport capacity: | Max 18242 slots, 10GE (sum of both interfaces) | (short term): | -5 to 55 oC (23 to 131 oF) |
| Storage temp: | -40 to 70oC (-40 to 156 oF) | ||
| Supported standards: | Relative humid: | 10% to 90% (non-condensing) | |
| IEEE 802.3 | Ethernet | ||
| IEEE 802.1Q | Virtual LANs | Power consumption: <50w | |
| IEEE 802.1p | Ethernet User Priority | ||
| RFC2474 | IP Diffserv Priority | Regulatory compliance: | |
| RFC826, RFC903 | Address Resolution protocols ARP | Safety: | IEC/EN 60950-1 |
| RFC768 | User Datagram Protocol UDP | CE marking: | 93/68/EEC |
| EMC: | ETSI EN 300 386 FCC Part 15 sub-part B | ||
| Performance management: | RoHS directive: | 2002/95/EC | |
| 24h/15m bins: | ES/SES/UAS/BBE/SS | ||
| IP: | DPP-IP counters PDV Max, RMS, 99.9% | ||
| Ethernet: | MIB-2/ifgroup and RMON | Ordering information: | |
| Synchronization: | Normal, Degraded, Failed | NPK0022-TR01 | 1GE Trunk Module Kit |
| NPK0022-TR10 | 10GE Trunk Module Kit | ||
| Maintenance: | NPS0056-6001 | 10GE Module | |
| Hardware: | Hot swap | NPM0036-01GU | 1GE Uplink Option |
| Firmware: | Remote SW/FW upgrade | NPM0036-10GU | 10GE/1GE Uplink Option |
| TECHNICAL SPECIFICATIONS | |||
| Dimensions: | 88mm(3.5’’)x445mm(17.5’’) x240mm(9.4’’), | Performance Management: | |
| (HxWxD) | IEC 60297 (19’’), ETSI EN 300 119 compatible. | Based on ITU-T G.826 with 15min/24h bins. Parameters: ES/SES/UAS/BBE/SS. IP link statistics with real-time precision monitoring of packet delay variation properties. | |
| Number of slots: | 2, for Nimbra 300 series plugin modules. | ||
| Fixed Gigabit Ethernet Access: | |||
| Interface: | 4 x 1000BASE-T, RJ45, 4x SFP bays for Giga-bit Ethernet SFPs. | Management: | |
| Standards: | 802.1Q/1p, Diffserv, Jumbo frames, bridged or transparent mode, fault propagation, hitless 1+1 protection switching. | SNMP v1/v2c/v3, Element Manager, Nimbra Vision | |
| Capacity: | 10 Gbps Ethernet switch capacity, 8 virtual Ethernet switches. | ||
| Environmental conditions: | |||
| Fixed uplink ports: | 4x IP/Ethernet: 1000BASE-T (10/100/1000) or 1000BASE-SX/LX/ZX SFPs. Up to 16 trunks can be mapped on the four uplink ports. Trunks support DTC (Dynamic Trunk Capacity) and 1D/2D FEC. | Operating temp: | 5 to 40 oC (41 to 104 oF) |
| (short term): | -5 to 55 oC (23 to 131 oF) | ||
| MSR Switch capacity: | 5 Gbps (inter-module) | Storage temp: | -40 to 70oC (-40 to 156 oF) |
| Relative humid: | 10% to 90% (non-condensing) | ||
| Regulatory compliance: | Available plug-in units: | ||
| Safety: | IEC/UL/EN60950-1 | 8 x SDI Video Access, 8 x ASI transport Access, 4 x OC-3/STM-1Access, 4 x DS3/E3 Access, 8 x E1/T1 Access, 8 x AES/EBU Access, 4 x DS3/E3 Trunk, 4 x OC-3/STM-1 Trunk, 2 x OC-12/STM-4 Trunk, 2 x OC-48/STM-16 Trunk | |
| Laser safety: | CFR 21 1040.10/11 | ||
| EMC: | FCC 15 Class A, EN 300 386 | ||
| CE marking: | 93/68/EEC | ||
| Power: | |||
| Input: | 2 x -48 VDC (-60 to -40 VDC) (115/230VAC with external converter) | ||
| Dissipation: | <90w fully equipped | ||
| Ordering information: | |||
| Synchronization: | NPK0024-DWB1 | Nimbra 390 Base Unit (1 trunk incl) | |
| Input: | 2.048 MHz (1.544 Mhz), ITU-T G.703.13 | NPM0041-MT3F | Additional Trunk feat lic |
| Output: | 2.048 MHz, ITU-T G.703.13. | NPM0045-3EAF | Ethernet Access feat lic |
| Internal oscillator: | Stratum 3 | NPM0020 | -300F Ethernet Switching feat lic |
| Time Transfer: | 2 x 1 PPS + 2 x 10 MHz, 50 Ohm BNC, in/out | NPM0035-EH3F | Hitless ETS 1+1 feat lic |
| (optional) | IRIG-B004 ToD interface | NPM0017-36T1 | Time Transfer RTU license |
| NPM0042-IR3R | IRIG-B RTU license | ||
| Alarm I/O: | DSUB-9, 6 inputs / 1 output | NPA0031-3120 | AC/DC Converter |
| TECHNICAL SPECIFICATIONS | ||||
| Dimensions: | 88mm(3.5’’) x 445mm(17.5’’) x 240mm(9.4’’), | Alarm I/O: | DSUB-9, 6 inputs / 1 output | |
| (HxWxD) | IEC 60297 (19’’), ETSI EN 300 119 compatible | |||
| Management: | ||||
| Number of slots: | 2, can be fitted freely with Nimbra 300 series plug-in modules | SNMP: | v1/v2c/v3 | |
| Element Manager: | Web GUI, CLI | |||
| Network Manager: | Nimbra Vision | |||
| Fixed Ethernet access: | ||||
| 8 x Gigabit Ethernet: 8 x 1000BASE-T, RJ45, 802.1Q/1p, Diffserv, Jumbo frames, bridged or transparent mode | Environmental conditions: | |||
| Operating temp: | 5 to 40 oC (41 to 104 oF) | |||
| (short term): | -5 to 55 oC (23 to 131 oF) | |||
| Fixed trunk ports: | Storage temp: | -40 to 70oC (-40 to 156 oF) | ||
| 4 x OC-3/STM-1: (included) | 4 SFP ports, STS-3c (ANSI T1.105)/STM-1 (ITU-T G.707) framing, SRS-3c SPE/VC-4 mapping. | Relative humid: | 10% to 90% (non-condensing) | |
| 4 x OC-12/STM-4: (firmware option) | 4 SFP ports, STS-12c (ANSI T1.105)/STM-4 (ITU-T G.707) framing, SRS-12c SPE/VC-4-4c mapping. | |||
| 2 x OC-48/STM-16: (firmware option) | 2 SFP ports, STS-48c (ANSI T1.105)/STM-16 (ITU-T G.707) framing, SRS-48c SPE/VC-4-16c mapping. | Regulatory compliance: | ||
| 2 x IP/Ethernet: (firmware option) | 1000BASE-T (10/100/1000) or 1000BASE-SX/LX (optical) SFPs. | Safety: | UL60950-1 EN60950-1 | |
| Laser safety: | CFR 21 1040.10/11 | |||
| Switch capacity: | 5 Gbps (inter-module) | EMC | FCC 15 Class A | |
| EN 300 386 | ||||
| Power: | CE marking | 93/68/EE | ||
| Voltage: | 2 x -48 VDC (-60 to -40 VDC) (115/230VAC with external converter) | Available plug-in units: | ||
| Dissipation: | <90w fully equipped | 4 x SDI Video Access | 8 x ASI transport Access | |
| 1 x Gigabit Ethernet | 8 x Fast Ethernet | |||
| Synchronization: | 4 x OC-3/STM-1 Access | 4 x DS3/E3 Access | ||
| Input: | 2.048 MHz (1.544 Mhz), ITU-T G.703 §13 | 8 x E1/T1 Access | 8 x AES/EBU Access | |
| Output: | 2.048 MHz, ITU-T G.703 §13 | |||
| Internal osc: | Stratum 3 | Ordering information: | ||
| Time Transfer: (firmware option) | 2 x 1 PPS + 2 x 10 MHz, 50 Ohm BNC, in/out | NPQ0015-DW01 | Nimbra 380 Base Unit, including 4 x OC-3/STM-1 trunk firmware | |
| Performance Management: Based on ITU-T G.826 | NPM0016-3004 | 4 x OC-12/STM-4 trunk firmware license | ||
| Bins: | 15min/24h bins | NPM0016-3016 | 2 x OC-48/STM-16 trunk firmware license | |
| Parameters: | ES/SES/UAS/BBE/SS | NPM0016-3ET2 | 2 x IP/Ethernet trunk firmware license | |
| NPM0020-3001 | Ethernet switching feature license | |||
| NPM0017-36T1 | Time Transfer firmware license | |||
| NPA0031-3401 | AC/DC Converter | |||
| TECHNICAL SPECIFICATIONS | |||
| Dimensions: | 66 mm(2,6’’) x 445mm(17.5’’) x 240mm(9.4’’), | Performance Management: Based on ITU-T G.826 | |
| (HxWxD) | IEC 60297 (19’’), ETSI EN 300 119 compatible | Bins: | 15min/24h bins |
| Parameters: | ES/SES/UAS/BBE/SS | ||
| Number of slots: | 1, can be fitted with any Nimbra 300 series plug-in module | ||
| Management: | |||
| SNMP: | v1/v2c/v3 | ||
| Fixed Ethernet access: | Element Manager: | Web GUI, CLI | |
| 8 x Gigabit Ethernet: 8 x 1000BASE-T, RJ45, 802.1Q/1p, Diffserv, Jumbo frames, bridged or transparent mode | Network Manager: | Nimbra Vision | |
| Environmental conditions: | |||
| Fixed trunk ports: | Operating temp: | 5 to 40 oC (41 to 104 oF) | |
| 2 x OC-3/STM-1: (included) | 2 SFP ports, STS-3c (ANSI T1.105)/STM-1 (ITU-T G.707) framing, SRS-3c SPE/VC-4 mapping. | (short term): | -5 to 55 oC (23 to 131 oF) |
| 2 x OC-12/STM-4: (firmware option) | 2 SFP ports, STS-12c (ANSI T1.105)/STM-4 (ITU-T G.707) framing, SRS-12c SPE/VC-4-4c mapping. | Storage temp: | -40 to 70oC (-40 to 156 oF) |
| 2 x OC-48/STM-16: (firmware option) | 2 SFP ports, STS-48c (ANSI T1.105)/STM-16 (ITU-T G.707) framing, SRS-48c SPE/VC-4-16c mapping. | Relative humid: | 10% to 90% (non-condensing) |
| 2 x IP/Ethernet: (firmware option) | 1000BASE-T (10/100/1000) or 1000BASE-SX/LX (optical) SFPs. | ||
| Regulatory compliance: | |||
| Safety: | UL60950-1 EN60950-1 | ||
| Laser safety: | CFR 21 1040.10/11 | ||
| EMC: | FCC 15 Class A EN 300 386 | ||
| Switch capacity: | 5 Gbps (inter-module) | CE marking: | 93/68/EE |
| Power: | Available plug-in units: | ||
| Voltage: | 2 x -48 VDC (-60 to -40 VDC) (115/230VAC | SDI Video Access | DS3/E3 Trunk/Access |
| with external converter) | Gigabit Ethernet | AES/EBU Access | |
| Dissipation: | <70w fully equipped | OC-3/STM-1 Access | IP/Ethernet Trunk |
| E1/T1 Access | OC-3/STM-1 Trunk | ||
| Synchronization: | ASI transport Access | OC-12/STM-4 Trunk | |
| Input: | 2.048 MHz (1.544 Mhz), ITU-T G.703 §13 | Fast Ethernet Access | OC-48/STM-16 trunk |
| Output: | 2.048 MHz, ITU-T G.703 §13 | ||
| Internal osc: | Stratum 3 | Ordering information: | |
| Time Transfer: (firmware option) | 1 PPS + 10 Mhz, 50 Ohm BNC, in/out | NPQ0018-DW01 | Nimbra 320 Base Unit, including 2 x OC-3/STM-1 |
| trunk firmware | |||
| NPM0016-3004 | OC-12/STM-4 trunk firmware license | ||
| NPM0016-3016 | OC-48/STM-16 trunk firmware license | ||
| NPM0016-3ET2 | IP/Ethernet trunk firmware license | ||
| NPM0020-3001 | Ethernet switching feature license | ||
| NPM0017-36T1 | Time Transfer feature license | ||
| NPA0031-3401 | AC/DC Converter | ||
| TECHNICAL SPECIFICATIONS | |||||
| Form factor: | Plug-in unit for Nimbra 300 series, uses 1 slot | Management: | |||
| SNMP: | v1/v2c/v3 | ||||
| Ports: | 8 x SDI In or Out, individually configurable, 1 monitor, BNC 75 ohm | Element Manager: | Web GUI, CLI, Nimbra Vision | ||
| Maintenance: | |||||
| Interface: | Hardware: | Hot-swap | |||
| Standard: | SMPTE 259M SD-SDI SMPTE 305M SD-SDTI | Firmware: | Remote upgrade | ||
| Frequency: | 270 Mbps | ||||
| Input freq toler | ± 40 ppm | Power consumption: | <20w | ||
| Return loss: | >17 dB | ||||
| Reach: | Up to 300 m, Belden 1694A | Environmental conditions: | |||
| Operating temp: | 5 to 40 oC (41 to 104 oF) | ||||
| (short term): | -5 to 55 oC (23 to 131 oF) | ||||
| Mapping: | Storage temp: | -40 to 70 oC (-40 to 156 oF) | |||
| DTM: | ETSI ES 201 803-11 | Relative humid: | 10% to 90% (non-condensing) | ||
| Jitter: | |||||
| PCR: | Regulatory compliance: | ||||
| Safety: | UL60950 EN60950 | ||||
| Fault management: | EMC: | FCC Part 15 sub-part B EN 300 386 | |||
| RX: | LOS, LOF, DOF, LOL | CE marking: | 93/68/EEC | ||
| TX: | AIS, LODS, DUF, DOF | Environmental: | RoHS directive 2002/95/EC | ||
| Performance management: ITU-T G.826 based | |||||
| Bins: | 24h, 15min | Ordering information: | |||
| Parameters: | ES, SES, BBE, UAS | NPS0048-3001 | 8 x SDI Video Access Module (Nimbra 300 series) | ||
| TECHNICAL SPECIFICATIONS | |||
| Form factor: | Plug-in unit for Nimbra 300 series, uses 1 slot | Maintenance: | |
| Hardware: | Hot-swap | ||
| Ports: | 8 x DVB-ASI In or Out, individually configurable, 1 monitor, BNC 75 ohm | Firmware: Remote upgrade | |
| Interface: | Power consumption: <20w | ||
| Standard: | DVB-ASI, CENELEC EN 50083-9 | ||
| Frequency: | 270 Mbps | Environmental conditions: | |
| Input freq toler: | ± 100 ppm | Operating temp: | 5 to 40 oC (41 to 104 oF) |
| Output freq: | ± 20 ppm | (short term): | -5 to 55 oC (23 to 131 oF) |
| Return loss: | >17 dB (27-270 MHz) | Storage temp: | -40 to 70 oC (-40 to 156 oF) |
| Signal amplitude: | 800 mV +-10% | Relative humid: | 10% to 90% (non-condensing) |
| DC offset: | +0.5 to -0.5 V | ||
| Rise and fall times: | (20%-80%) max 1.2 ns | Regulatory compliance: | |
| Reach: | 275 m (900 feet), Belden 1694A | Safety: | UL60950 EN60950 |
| EMC: | FCC Part 15 sub-part B EN 300 386 | ||
| Mapping: | CE marking: | 93/68/EEC | |
| DTM: | ETSI ES 201 803-11 | Environmental: | RoHS directive 2002/95/EC |
| TS Bandwidth: | 2 – 212 Mbps | ||
| Jitter: | |||
| PCR: | < ± 150 ns (no PCR re-stamping) | Ordering information: | |
| NPS0031-3001: | 8 x ASI Transport Access Module | ||
| Fault management: | |||
| RX: | LOS, LOF, DOF, LOL | ||
| TX: | AIS, LODS, DUF, DOF | ||
| Performance management: | |||
| ITU-T G.826 based | |||
| Bins: | 24h, 15min | ||
| Parameters: | ES, SES, BBE, UAS | ||
| Management: | |||
| SNMP: | v1/v2c/v3 | ||
| Element Manager: | Web GUI, CLI, Nimbra Vision | ||
| TECHNICAL SPECIFICATIONS | |||
| Form factor: | Plug-in unit for Nimbra 300 series, 1 slot | Maintenance: | |
| Hardware: | Hot swap | ||
| Ports: | 8 x Digital Audio In or Out, individually configurable. 1 monitor, BNC 75 ohm, to AES-3id-2001 | Firmware: | Remote upgrade |
| Power consumption: <12w | |||
| Interface: | Management: | ||
| Standards: | AES3/5/11-2003, AES-3id-2001 | SNMP: | v1/v2c/v3 |
| Sample rates: | 32/48/96/192/44.1/88.2/176.4 kHz | Element Manager: | Web GUI, CLI |
| Input freq toler: | ± 10 ppm | Network Manager: | Nimbra Vision |
| Return loss: | >20 dB | ||
| Reach: | 330 m (1000 feet), Belden 1694AMapping: | Environmental conditions: | |
| Operating temp: | 5 to 40 oC (41 to 104 oF) | ||
| Mapping: | (short term): | -5 to 55 oC (23 to 131 oF) | |
| DTM: ETSI ES 201 803-11 | Storage temp: | -40 to 70oC (-40 to 156 oF) | |
| Relative humid: | 10% to 90% (non-condensing) | ||
| Jitter: | |||
| Output intrinsic: | < 0.025 UI pp @ 48 kHz | Regulatory compliance: | |
| Input tolerance: | 0.25 UI @ >8kHz | Safety: | UL60950 |
| Latency: | < 1 ms through board | EN60950 | |
| EMC: | FCC Part 15 sub-part B EN 300 386 | ||
| Fault management: | CE marking: | 93/68/EEC | |
| RX: | LOS, LOF, DOF, LOL | Environmental: | RoHS directive 2002/95/EC |
| TX: | AIS, DUF, DOF | ||
| Performance management: | Ordering information: | ||
| ITU-T G.826 based | NPS0050-3001 | 8 x AES/EBU Access Module (Nimbra 300 series) | |
| Bins: | 24h, 15min | ||
| Parameters: | ES, SES, BBE, UAS | ||
| TECHNICAL SPECIFICATIONS | |||
| Form factor: | Plug-in unit to Nimbra 300 series, uses 1 slot. | Maintenance: | |
| Hardware: | Hot swap | ||
| Physical Interface: | Firmware: | Remote firmware upgrade | |
| Interface type: | SFP ports | ||
| Number of ports: | 3 | Management: | |
| Supported SFPs: | 1000BASE-T, 1000BASE-SX/LX | SNMP: | v1/v2c/v3 |
| Port speed: | 10, 100 or 1000 Mbps full duplex auto sensing | ElementManager: | Web GUI, CLI |
| (1000BASE-T), 1000 Mbps (1000BASE-SX/LX) | Network Manager: | Nimbra Vision | |
| Mapping: | Timing and Synchronization: | ||
| Encapsulation: | DTM over DPP-IP/UDP/IP/Ethernet | Modes: | Network timing |
| FEC: | Adapted SMPTE 2022 / COP | Hold-over/Local | |
| Bw. granularity: | 0.5 Mbps | External refeference | |
| Supported standards: | Environmental conditions: | ||
| IEEE 802.3 | Ethernet | Operating temp: | 5 to 40 oC (41 to 104 oF) |
| IEEE 802.1Q | Virtual LANs | (short term): | -5 to 55 oC (23 to 131 oF) |
| IEEE 802.1p | Ethernet User Priority | Storage temp: | -40 to 70oC (-40 to 156 oF) |
| RFC2474 | IP Diffserv Priority | Relative humid: | 10% to 90% (non-condensing) |
| RFC826, RFC903 | Address Resolution protocols ARP | ||
| RFC768 | User Datagram Protocol UDP | Power consumption: <20w | |
| Fault management: | Regulatory compliance: | ||
| Defects: | dLOS, dLOF, dLOP, dLOM, dAIS, dRDI, dDEG | Safety: | IEC/EN 60950-1 |
| Alarms: | Communication and Equipment | CE marking: | 93/68/EEC |
| EMC: | ETSI EN 300 386 FCC Part 15 sub-part B | ||
| Performance management: | RoHS directive: | 2002/95/EC | |
| 24h/15min bins: | ES, SES, BBE, UAS, SS | ||
| IP: | UDP Checksum | ||
| Ethernet: | MIB-2/RMON counters statistics group | Ordering information: | |
| NPS0053-3001 | 3 x IP/Ethernet Trunk Module (300) | ||
| NPM0016-3ET2 | 2 x IP/ETH Trunk Firmware for Nimbra 300 | ||
| (Note: The 3 x IP/Ethernet Trunk Module is not supported by the Nimbra 390) | |||
| TECHNICAL SPECIFICATIONS (DOWNLOAD PDS) | |
| Container format: MPEG-TS (SPTS or MPTS) | |
| Transport format: RTP, UDP/IP Unicast or Multicast | |
| Interfaces | 2x Gigabit Ethernet, 1000BASE-T, RJ-45 |
| Networking | Path Protection (ARQ): RIST, SRT, Zixi, Edge Connect, FEC |
| Redundancy: Link Bonding, Adaptive Link Protection with SMPTE 2022-7 style redundancy, Adaptive Source Protection | |
| Ingress & Egress Handoff: TSoIP (UDP/IP) Unicast & Multicast with optional FEC (SMPTE 2022-1) | |
| Security: Embedded Firewall, Remote VPN capabilities, DTLS based Video Encryption & Authentication | |
| Performance Monitoring | Video: ETR 290, TR-101 290 Priority 1 & Priority 2, Transport Stream information for PAT, PMT, PCR, NULL Packets, Video, Audio and Data stream details, Thumbnails |
| IP & Ethernet: Packet counters, loss, delay, delay variation | |
| Management | Protocols: SNMP (v1/v2c/v3) |
| Element Manager: Graphical Web UI | |
| NMS Support: Nimbra Vision for alarms, provisioning & performance, Touch & Switch for rapid service activation, Customer Provisioned Networks for powerful scheduling & booking | |
| Customizable Node Alarms: Bitrate threshold (UDP), Unrecovered packets, Stream supervision (ANC and audio) | |
| Power & Environmental | Power: Single or dual 400W hot-swappable AC/DC gold level power supply |
| Operating temperature: 5 to 35 °C (41 to 95 °F) | |
| Storage temperature: -40 to 70°C (-40 to 158°F) | |
| Relative humidity: 8% to 90% (non-condensing) | |
| Regulatory Compliance | Safety: IEC/UL/EN 60 950-1 |
| EMC: FCC part 15B, EN 55022, EN 55024, EN 55103-2, EN 55032, EN 61000-3-2, EN 61000-3-3 | |
| CE Marking: 768/2008 | |
| Dimensions: HxWxD: 43mm(1.7”) x 437mm(17.2”) x 429mm(16.9”) | |
| Weight: 8.16 kg (18 lbs) | |
| Rack mount: 1RU, IEC 60297 (19’’) | |
| TECHNICAL SPECIFICATIONS (DOWNLOAD PDS) | |
| Input formats | Video: SMPTE 2022-2, SMPTE 259M, SMPTE 292M, SMPTE 424M |
| Audio: AAC-LC, HE-AAC, MPEG-2 layer II, AES3, Passthrough | |
| Container format: MPEG-TS (SPTS or MPTS) | |
| Transport format: RTP, UDP/IP Unicast or Multicast | |
| Resolutions: SD 480 and 576. HD 720 and 1080 | |
| Scan mode: Progressive and interlaced | |
| Frame rates: 25, 29.97, 30, 59.94, 50, 60 fps | |
| Chroma format: 4:2:0 | |
| Sample bit depth: 8-bit | |
| Onboard Signal Generator | |
| Video encoding formats | H.264 up to High Profile Level 4.2 |
| H.265 up to Main Profile Level 4.1 | |
| Interfaces | 2x Gigabit Ethernet, 1000BASE-T, RJ-45 |
| 2x 3G-SDI HD-BNC, 75 ohm + 1x Genlock input | |
| Networking | Path Protection (ARQ): RIST, SRT, Zixi, Edge Connect, FEC |
| Redundancy: Link Bonding, Adaptive Link Protection with SMPTE 2022-7 style redundancy, Adaptive Source Protection | |
| Ingress & Egress Handoff: TSoIP (UDP/IP) Unicast & Multicast with optional FEC (SMPTE 2022-1) | |
| Security: Embedded Firewall, Remote VPN capabilities, DTLS based Video Encryption & Authentication | |
| Performance Monitoring | Video: ETR 290, TR-101 290 Priority 1 & Priority 2, Transport Stream information for PAT, PMT, PCR, NULL Packets, Video, Audio and Data stream details, Thumbnails |
| IP & Ethernet: Packet counters, loss, delay, delay variation | |
| Management | Protocols: SNMP (v1/v2c/v3) |
| Element Manager: Graphical Web UI | |
| NMS Support: Nimbra Vision for alarms, provisioning & performance, Touch & Switch for rapid service activation, Customer Provisioned Networks for powerful scheduling & booking | |
| Customizable Node Alarms: Bitrate threshold (UDP), Unrecovered packets, Stream supervision (ANC and audio) | |
| Power & Environmental | Power: Single or dual 400W hot-swappable AC/DC gold level power supply |
| Operating temperature: 5 to 35 °C (41 to 95 °F) | |
| Storage temperature: -40 to 70°C (-40 to 158°F) | |
| Relative humidity: 8% to 90% (non-condensing) | |
| Regulatory Compliance | Safety: IEC/UL/EN 60 950-1 |
| EMC: FCC part 15B, EN 55022, EN 55024, EN 55103-2, EN 55032, EN 61000-3-2, EN 61000-3-3 | |
| CE Marking: 768/2008 | |
| Dimensions: HxWxD: 43mm(1.7”) x 437mm(17.2”) x 429mm(16.9”) | |
| Weight: 8.16 kg (18 lbs) | |
| Rack mount: 1RU, IEC 60297 (19’’) | |
| TECHNICAL SPECIFICATIONS (DOWNLOAD PDS) | |
| Input formats | Video: SMPTE 2022-2, SMPTE 259M, SMPTE 292M, SMPTE 424M |
| Audio: AAC-LC, HE-AAC, MPEG-2 layer II, AES3, Passthrough | |
| Container format: MPEG-TS (SPTS or MPTS) | |
| Transport format: RTP, UDP/IP Unicast or Multicast | |
| Resolutions: SD 480 and 576. HD 720 and 1080 | |
| Scan mode: Progressive and interlaced | |
| Frame rates: 25, 29.97, 30, 59.94, 50, 60 fps | |
| Chroma format: 4:2:0 | |
| Sample bit depth: 8-bit | |
| Onboard Signal Generator | |
| Video encoding formats | H.264 up to High Profile Level 4.2 |
| H.265 up to Main Profile Level 4.1 | |
| Interfaces | 4x 10 Gb RJ-45, 1000BASE-T |
| 1x 12-G SDI HD-BNC, 75 ohm + 3x 3-G SDI HD-BNC, 75 ohm+ 1x Genlock input | |
| Networking | Path Protection (ARQ): RIST, SRT, Zixi, Edge Connect, FEC |
| Redundancy: Link Bonding, Adaptive Link Protection with SMPTE 2022-7 style redundancy, Adaptive Source Protection | |
| Ingress & Egress Handoff: TSoIP (UDP/IP) Unicast & Multicast with optional FEC (SMPTE 2022-1) | |
| Security: Embedded Firewall, Remote VPN capabilities, DTLS based Video Encryption & Authentication | |
| Performance Monitoring | Video: ETR 290, TR-101 290 Priority 1 & Priority 2, Transport Stream information for PAT, PMT, PCR, NULL Packets, Video, Audio and Data stream details, Thumbnails |
| IP & Ethernet: Packet counters, loss, delay, delay variation | |
| Management | Protocols: SNMP (v1/v2c/v3) |
| Element Manager: Graphical Web UI | |
| NMS Support: Nimbra Vision for alarms, provisioning & performance, Touch & Switch for rapid service activation, Customer Provisioned Networks for powerful scheduling & booking | |
| Customizable Node Alarms: Bitrate threshold (UDP), Unrecovered packets, Stream supervision (ANC and audio) | |
| Power & Environmental | Power: Single or dual 400W hot-swappable AC/DC gold level power supply |
| Operating temperature: 5 to 35 °C (41 to 95 °F) | |
| Storage temperature: -40 to 70°C (-40 to 158°F) | |
| Relative humidity: 8% to 90% (non-condensing) | |
| Regulatory Compliance | Safety: IEC/UL/EN 60 950-1 |
| EMC: FCC part 15B, EN 55022, EN 55024, EN 55103-2, EN 55032, EN 61000-3-2, EN 61000-3-3 | |
| CE Marking: 768/2008 | |
| Dimensions: HxWxD: 43mm(1.7”) x 437mm(17.2”) x 429mm(16.9”) | |
| Weight: 8.16 kg (18 lbs) | |
| Rack mount: 1RU, IEC 60297 (19’’) | |
| TECHNICAL SPECIFICATIONS | |
| Input formats | Video: H.264 up to High Profile Level 4.2, H.265 up to Main Profile Level 4.1 Audio: AAC-LC, HE-AAC, MPEG-2 layer II, AES3, Passthrough Container format: MPEG-TS (SPTS or MPTS) Transport format: RTP, UDP/IP Unicast or Multicast Resolutions: SD 480 and 576. HD 720 and 1080 Scan mode: Progressive and interlaced Frame rates: 25, 29.97, 30, 59.94, 50, 60 fps Chroma format: 4:2:0 Sample bit depth: 8-bit |
| Video encoding formats | SMPTE 2022-2 SMPTE 259M SMPTE 292M SMPTE 424M |
| Interfaces | 2x Gigabit Ethernet, 1000BASE-T, RJ-45 2x 10 Gigabit Ethernet, 10GBASE-T, RJ-45 4x DIN 1.01 2.3, 75 ohm, 1x DIN 1.01 2.3, 75 ohm Genlock input |
| Networking | Internet Transport: Net Insight Advanced Error Protected Transport, RIST, Bonding, Adaptive Link Protection, Adaptive Source Protection Ingress & Egress Handoff: TSoIP (UDP/IP) Unicast & Multicast with optional FEC (SMPTE 2022-1) Security: Embedded Firewall, Remote VPN capabilities, Video Encryption |
| Performance Monitoring | Video: ETR 290, TR-101 290 Priority 1 & Priority 2, Transport Stream information for PAT, PMT, PCR, NULL Packets, Video and Audio stream details, Thumbnails IP & Ethernet: Packet counters, loss, delay, delay variation |
| Management | Protocols: SNMP (v1/v2c/v3) Element Manager: Graphical Web UI NMS Support: Nimbra Vision for alarms, provisioning & performance, Touch & Switch for rapid service activation, Customer Provisioned Networks for powerful scheduling & booking Customizable Node Alarms: Bitrate threshold (UDP), Unrecovered packets, Stream supervision (ANC and audio) |
| Power & Environmental | Power: 200W Low Noise AC-DC gold level power supply Operating temperature: 5 to 35 °C (41 to 95 °F) Storage temperature: -40 to 70°C (-40 to 158°F) Relative humidity: 8% to 90% (non-condensing) |
| Regulatory Compliance | Safety: IEC/UL/EN 60 950-1 EMC: FCC part 15B, EN 55022, EN 55024, EN 55103-2, EN 55032, EN 61000-3-2, EN 61000-3-3 CE Marking: 768/2008 Dimensions: HxWxD: 43mm(1,7”) x 437mm(17,2”) x 287mm(11,3”) Weight: 4.56 kg (10.1 lbs) Rack mount: 1RU, IEC 60297 (19’’) |
| TECHNICAL SPECIFICATIONS | |||
| Dimensions | 44mm x 440mm x 252mm, (HxWxD) | IGMP Immediate Leave | |
| IGMP Querier | |||
| Physical Ports | 12 Gigabit Combo (RJ45/SFP) ports Dual power input (1 AC + 1 DC) 1 Out of band management port (RJ45) 1 Console Port (RJ45) 1 DB15 Alarm I/O Port | Port Mirroring | |
| Jumbo frames: | Up to 10KB | ||
| Performance | 12 Gbps switching capacity 16K Mac address table | ||
| Security features | |||
| QoS Features | Access Control List: | MAC access control list IP standard access control list IP extended access control list | |
| Priority Queues: | 8 hardware queues per port | ||
| Traffic classification: | IEEE 802.1p CoS IP Precedence DSCP | Management: | SSH (v1.5/v2.0) SSL for HTTPS SNMPv3 |
| Traffic Scheduling: | Strict Priority Weighted Round Robin Strict + WRR traffic scheduling | ||
| Environmental Conditions | |||
| Layer2 Features | Operating Temp: | -25C to 65C | |
| Spanning Tree | IEEE 802.1D Spanning Tree Protocol (STP) | Storage Temp: | -40C to 70C |
| Protocols: | IEEE 802.1w Rapid Spanning Tree Protocol (RSTP) IEEE 802.1s Multiple Spanning Tree Protocol (MSTP) | Humidity: | 10% to 90% (Non-condensing) |
| Supported VLANs: | 4K VLAN Port-based VLAN IEEE 802.1Q VLAN Virtual Private VLAN QinQ | ||
| Link Aggregation: | Static Trunk IEEE 802.3ad Link Aggregation Control Protocol Trunk groups: 12, up to 8 ports per group | Power | |
| IGMP Snooping: | IGMP v1/v2/v3 snooping IGMP Proxy reporting IGMP Filtering IGMP Throttling | AC input: | 100-240 VAC, 50-60Hz |
| DC input: | -42V — 56V | ||
| Regulatory | |||
| Safety: | UL(CSA 22.2. NO 60950-1 & UL60950-1) | Power Consumption: < 20W, Dying Gasp support | |
| EMC: | CB(IEC60950-1) CE Mark, FCC Class A, CISPR Class A | ||
| Ordering information: | |||
| Management: | NPQ0016-XW01 | Nimbra 230 Metro Access Switch | |
| SNMP: | v1/v2c/v3 | ||
| Element Manager: | Web GUI, CLI | ||
| Network Manager: | Nimbra Vision (Optional) | ||
| TECHNICAL SPECIFICATIONS | |||
| NI-102 | Conformance | ||
| Network Monitoring Card with 10Base-T Ethernet connection in front. | EMI/RFI | Complies with 2004/108/EC | |
| Electrical | Complies withEN 61000-6-1, EN61000-6-2 | ||
| Optional – 1 required per frame. | RoHS | Complies with Directive 2002/95/EC | |
| General Frame Specifications | Ordering Information | ||
| NPQ0020-AW01 Nimbra 141. 19”” 1RU Chassis for up to 6 MMS Cards. Includes Dual Redundant Power Supplies. Monitoring card is optional and available via front panel slot. | |||
| Depth: | 150 mm (excluding connectors) | ||
| Width: | 445 mm | ||
| Height: | 44.5 mm (1RU) | ||
| Weight: | 4.5 kg when fully loaded | ||
| Operating Temp: | -30 to +70 °C | ||
| Voltage Range: | 90 to 260 VAC 50/60 Hz | NPQ0020-AW01 | Nimbra 141P, 19” 1RU Chassis for up to 6 Passive NI-xxx Cards. No psu or monitoring capability. |
| Power: | 18 W when fully loaded | ||
| Signal detect: | Contact closure for psu failure | ||
| No of slots: | 6 | ||
| 1 Network Monitoring board slot ( Not Nimbra 141P ) | NPS0078-1401 | NI-102. Network Monitoring Card with Ethernet connection. | |
| TECHNICAL SPECIFICATIONS | |||
| NI-102 | Conformance | ||
| Network Monitoring Card with Ethernet 10Base-T connection for Slot-16. | |||
| NI-102 can only be fitted in a Nimbra 143 V2 or Nimbra 141 V2 frame | EMI/RFI | Complies with 2004/108/EC | |
| Optional – 1 required per frame | Electrical | Complies with EN 61000-6-1, EN 61000-6-2 | |
| RoHS | Complies with Directive 2002/95/EC | ||
| General frame specifications | |||
| Depth: | 250 mm | Ordering information | |
| Width: | 445mm | NPQ0019-AW01 | Nimbra 143 (AC) 19” 3RU Chassis for up to 15 MMS Cards with optional Network Monitoring and including Dual Redundant Power Supplies |
| Height: | 132.5 mm (3RU) | NPS0078-1401 | NI-102 Network Monitoring Card with Ethernet connection. Can only be fitted in V2 chassis. |
| Operating Temp | -113 0k gt ow +h7e0n° fCully loaded | ||
| Voltage Range: | 90 to 250 VAC 47 to 663 Hz | ||
| Power: | 65 W when fully loaded | ||
| Signal detect: | Contact closure for psu failure | ||
| No of slots: | 15 Traffic modules slots 1 Network monitor slot | ||
| TECHNICAL SPECIFICATIONS | |||||
| Optical Input SFPs for different applications are ordered separately | Weight: | 100 g | |||
| Operating Temp: | -30 to +70°C | ||||
| Power: | 3 W | ||||
| Signal detect: | LED on for loss of signal | ||||
| Electrical Output | No. of slots: | 1 | |||
| Conformance | |||||
| Standards | SMPTE 424M, SMPTE 292M, SMPTE 259M, SMPTE297M, DVB-ASI Automatic rate selection for 3G, HD-SDI and SD-SDI data rates. | EMI/RFI | Complies with 2004/108/EC | ||
| Connector | 2 x 75 Ohm BNC per IEC 60169-8 Amendment 2 | Electrical | Complies with EN 61000-6-1, EN61000-6-2 | ||
| Return Loss | > 15 dB @ 1.485 Gb/s | Laser Safety | Complies with Class 1 laser product 24 CFR 1040.10 & 1040.11 | ||
| Polarity | 2 x Non inverting | ||||
| Signal Level | 800 mV +/- 10% | RoHS | Complies with Directive 2002/95/EC | ||
| DC Offset | 0 +/- 0.5 V | ||||
| Jitter | <0.15 UI line equalised | Ordering Information | |||
| Format | Reclocked | NPS0065-14R1 | NI-360R. Single Channel 3G/SDI Fiber Optic Receiver Card, Auto-Sensing and reclocking for SDI, ASI, HD/SDI and 3G/SDI – no optics fitted. | ||
| General Card Specifications | VIDEO SFP modules | ||||
| Depth: Width: Height: | 60 mm 20 mm 4TE 129 mm (3RU) | Standard Wavelengths | |||
| NPA0062-X2R1 | VR/S/SFP | SM 2-chan RX 1260-1620nm | |||
| NPA0062-MRT1 | VTR/S/SFP |
| |||
| TECHNICAL SPECIFICATIONS | ||||
| Electrical Input | Power | 3 W | ||
| Signal detect | LED on for loss of signal | |||
| Standards | SMPTE 424, SMPTE 292M, SMPTE 259M, | No. of slots | 1 | |
| SMPTE297M, DVB-ASI | ||||
| Equalisation | Automatic to 100 m @ 3 Gb/s | Conformance | ||
| Automatic to 200 m @ 1.485 Gb/s | ||||
| Automatic to 300 m @ 270 Mb/s | EMI/RFI | Complies with 2004/108/EC | ||
| Equaliser and reclocking can be bypassed to | Electrical | Complies with EN 61000-6-1, EN61000-6-2 | ||
| support data rates down to 50 Mb/s | Laser Safety | Complies with Class 1 laser product | ||
| Connector | 75 Ohm BNC per IEC 60169-8 Amendment 2 | 24 CFR 1040.10 & 1040.11 | ||
| Return Loss | > 15 dB @ 1.485 Gb/ | RoHS | Complies with Directive 2002/95/EC | |
| Electrical Output | Ordering Information | |||
| Connector | 75 Ohm BNC per IEC 60169-8 Amendment 2 | NPS0065-14T1 | NI-360T | |
| Return Loss | > 15 dB @ 1.485 Gb/s | Single Channel 3G/SDI Fiber Optic Transmitter Card, Auto-Sensing and reclocking for SDI, ASI, HD/SDI and 3G/SDI – no optics fitted. | ||
| Polarity | Non inverting | |||
| Signal Level | 800 mV +/- 10% | |||
| DC Offset | 0 +/- 0.5 V | VIDEO SFP modules | ||
| Jitter | <0.15 UI line equalised | Standard Wavelengths | ||
| Format | Driven active loop out | NPA0062-M2T1 | VT/S/SFP/13/13 | SM 2-chan TX 1310nm |
| NPA0062-X2R1 | VR/S/SFP | SM 2-chan RX 1260-1620nm | ||
| Optical Output | ||||
| SFPs for different applications are ordered separately | CWDM Wavelengths | |||
| NPA0063-1270 | VT/S/SFP/CWDM/1270 | SM 1-chan TX 1270 nm | ||
| General Card Specifications | NPA0063-1290 | VT/S/SFP/CWDM/1290 | SM 1-chan TX 1290 nm | |
| NPA0063-1310 | VT/S/SFP/CWDM/1310 | SM 1-chan TX 1310 nm | ||
| NPA0063-1330 | VT/S/SFP/CWDM/1330 | SM 1-chan TX 1330 nm | ||
| Depth | 60 mm | NPA0063-1350 | VT/S/SFP/CWDM/1350 | SM 1-chan TX 1350 nm |
| Width | 20 mm 4TE | and so on | ||
| Height Weight Operating Temp | 129 mm (3RU) 100 g -30 to +70°C | NPA0063-1590 NPA0063-1610 | VT/S/SFP/CWDM/1590 VT/S/SFP/CWDM/1510 | SM 1-chan TX 1590 nm SM 1-chan TX 1610 nm |
| TECHNICAL SPECIFICATIONS | ||||
| Optical Input | Ordering Information | |||
| SFPs for different applications are ordered separately | NPS0066-14R1 | NI-362R | ||
| Dual Channel 3G/SDI FiberOptic Receiver Card, Auto-Sensing and | ||||
| Electrical Output | reclocking for SDI, ASI, | |||
| HD/SDI and 3G/SDI – no optics fitted. | ||||
| Standards | SMPTE 424M, SMPTE 292M, SMPTE 259M, | |||
| SMPTE297M, DVB-ASI | VIDEO SFP modules | |||
| Automatic rate selection for 3G, HD-SDI and | ||||
| SD-SDI data rates. | Standard Wavelengths | |||
| NPA0062-M2T1 | VT/S/SFP/13/13 | SM 2-chan TX | ||
| Connector | 2 x 75 Ohm BNC per IEC 60169-8 Amendment 2 | 1310nm | ||
| Return Loss | > 15 dB @ 1.485 Gb/s | NPA0064-3155 | VT/S/SFP/ CWDM/31/55 | SM 2-chan TX |
| Polarity | 2 x Non inverting | 1310nm,1550nm | ||
| Signal Level | 800 mV +/- 10% | NPA0062-X2R1 | VR/S/SFP | SM 2-chan RX |
| DC Offset | 0 +/- 0.5 V | 1260-1620nm | ||
| Jitter | <0.15 UI line equalised | NPA0062-MRT1 | VTR/S/SFP | SM 2-chan TX/ |
| Format | Reclocked | RX 1310nm, | ||
| General Card Specifications | CWDM Wavelengths | |||
| NPA0064-2729 | VT/S/SFP/CWDM/27/29 | SM 2-chan TX | ||
| Depth | 60 mm | 1270/1290nm | ||
| Width | 20 mm 4TE | |||
| Height | 129 mm (3RU) | NPA0064-3133 | VT/S/SFP/CWDM/31/33 | SM 2-chan TX |
| Weight | 100 g | 1310/1330nm | ||
| Operating Temp | -30 to +70°C | |||
| Power | 3 W | NPA0064-3537 | VT/S/SFP/CWDM/35/37 | SM 2-chan TX |
| Signal detect | LED on for loss of signal | 1350/1370nm | ||
| No. of slots | 1 | |||
| NPA0064-3941 | VT/S/SFP/CWDM/39/41 | SM 2-chan TX | ||
| Conformance | 1390/1410nm | |||
| EMI/RFI | Complies with 2004/108/EC | |||
| Electrical | Complies with EN 61000-6-1, EN61000-6-2 | NPA0064-4749 | VT/S/SFP/CWDM/47/49 | SM 2-chan TX |
| Laser Safety | Complies with Class 1 laser product | 1470/1490nm | ||
| 24 CFR 1040.10 & 1040.11 | ||||
| NPA0064-5153 | VT/S/SFP/CWDM/51/53 | SM 2-chan TX | ||
| RoHS | Complies with Directive 2002/95/EC | 1510/1530nm | ||
| (with bypass to support data rates down to 10 Mb/s) | NPA0064-5557 | VT/S/SFP/CWDM/55/57 | SM 2-chan TX | |
| 1550/1570nm | ||||
| TECHNICAL SPECIFICATIONS | ||||
| Electrical Input | Conformance | |||
| EMI/RFI | Complies with 2004/108/EC | |||
| Standards | SMPTE 424M, SMPTE 292M, SMPTE 259M, SMPTE297M, DVB-ASI | Electrical | Complies with EN 61000-6-1, EN61000-6-2 | |
| Laser Safety | Complies with Class 1 laser product 24 CFR 1040.10 & 1040.11 | |||
| Equalisation | Automatic to 100 m @ 3 Gb/s Automatic to 200 m @ 1.485 Gb/s Automatic to 300 m @ 270 Mb/s Equaliser and reclocking can be bypassed to support data rates down to 50 Mb/s | |||
| Connector | 75 Ohm BNC per IEC 60169-8 Amendment 2 | RoHS | Complies with Directive 2002/95/EC | |
| Return Loss | > 15 dB @ 1.485 Gb/s | |||
| Ordering Information | ||||
| Electrical Output | NPS0066-14T1 | NI-362T, Dual Channel 3G/SDI Fiber Optic Transmitter Card, Auto-Sensing and reclocking for SDI, ASI, HD/SDI and 3G/SDI – no optics fitted. | ||
| Connector | 75 Ohm BNC per IEC 60169-8 Amendment 2 | |||
| Return Loss | > 15 dB @ 1.485 Gb/s | |||
| Polarity | Non inverting | VIDEO SFP modules | ||
| Signal Level | 800 mV +/- 10% | Standard Wavelengths | ||
| DC Offset | 0 +/- 0.5 V | NPA0062-M2T1 | VT/S/SFP/13/13 1310nm | SM 2-chan TX |
| Jitter | <0.15 UI line equalised | NPA0064-3155 | VT/S/SFP/ CWDM/31/55 1310nm,1550nm | SM 2-chan TX |
| Format | Driven active loop out | NPA0062-X2R1 | VR/S/SFP 1260-1620nm | SM 2-chan RX |
| NPA0062-MRT1 | VTR/S/SFP RX 1310nm, | SM 2-chan TX/ | ||
| Optical Output SFPs for different applications are ordered separately | ||||
| CWDM Wavelengths | ||||
| General Card Specifications | NPA0064-2729 | VT/S/SFP/CWDM/27/29 1270/1290nm | SM 2-chan TX | |
| Depth | 60 mm | NPA0064-3133 | VT/S/SFP/CWDM/31/33 1310/1330nm | SM 2-chan TX |
| Width 20 mm 4TE | NPA0064-3537 | VT/S/SFP/CWDM/35/37 1350/1370nm | SM 2-chan TX | |
| Height | 129 mm (3RU) | NPA0064-3941 | VT/S/SFP/CWDM/39/41 1390/1410nm | SM 2-chan TX |
| Weight | 100 g | NPA0064-4749 | VT/S/SFP/CWDM/47/49 1470/1490nm | SM 2-chan TX |
| Operating Temp | -30 to +70°C | NPA0064-5153 | VT/S/SFP/CWDM/51/53 1510/1530nm | SM 2-chan TX |
| Power | 3 W | NPA0064-5557 | VT/S/SFP/CWDM/55/57 1550/1570nm | SM 2-chan TX |
| Signal detect | LED on for loss of signal | | ||
| No. of slots | 1 | |||
| TECHNICAL SPECIFICATIONS | |||
| Optical Input/Output SFPs for different applications are ordered separately | Conformance | ||
| EMI/RFI | Complies with 89/336/EEC, EN55022B, EN61000-4-2, EN61000-4-4-(Level 2), EN61000-4-4FTB, EN61000-4-5, EN61000-4-11 | ||
| Electrical | Complies with EN 61000-6-1, EN61000-6-2, EN61000-6-3, EN61000-6-4 | ||
| Electrical Input/Output SFPs for different applications are ordered separately | Laser Safety | dependent on SFP fitted Complies with Class 1 laser product | |
| RoHS | Complies with Directive 2002/95/EC | ||
| General Card Specifications | Ordering Information | ||
| Depth | 60 mm | NPS0082-14C2 | NI-368 2-Channel SFP wavelength converter ETH/SDI – no optics fitted. |
| Width | 20 mm | ||
| Height | 129 mm (3RU) | ||
| Weight | 100 g | ||
| Operating Temp | -30 to +70°C | ||
| Power | 2,5 W typical | ||
| No. of slots | 1 | ||
| TECHNICAL SPECIFICATIONS | |||||
| Electrical Input/Output | Operating Temp | -30 to +70°C | |||
| Connector | RJ45 | Power | 2.4 W | ||
| Number | 1 channel | No. of slots | 1 | ||
| Format | Full duplex 100/1000Base-FX Data Transmission 10/100/1000BaseT half/full duplex auto-negotiation | Signal detect | LED on for power LED on for network activity LED on for fibre activity | ||
| Cable Reach | >100 m Cat-5 100 BaseT | Conformance | |||
| > 50 m Cat-5 1000 BaseT | EMI/RFI | Complies with 2004/108/EC | |||
| Standard | IEEE 802.3 802.3 802.3u 802.3ab | 10 BaseT 100 BaseT 1000 BaseT | Electrical | Complies with EN 61000-6-1, EN61000-6-2 | |
| RoHS | Complies with Directive 2002/95/EC | ||||
| Optical Input/Output | |||||
| Connector | SFP cage | Ordering Information | |||
| NPS0079-1401 | NI-860. Singlemode Dual Fibre 10/100/1000 Base-T Ethernet to Fibre Converter Card with SFP cage. | ||||
| General Card Specifications | NPK0028-1470 | NI-860 kit including CWDM 1470 transceiver SFP | |||
| Depth | 60 mm | NPK0028-1490 | NI-860 kit including CWDM 1490 transceiver SFP | ||
| NPA0023-xxxx |
| ||||
| Width Height Weight | 20 mm 4TE 129 mm (3RU) 100 g | ||||
| TECHNICAL SPECIFICATIONS | |||
| Technical Specifications | General Card Specifications | ||
| Depth | 60 mm | ||
| Connector: | LC | Width | 20 mm 4TE |
| Wavelength: | 1310nm and 1550nm | Height | 129 mm (3RU) |
| Weight | 100 g | ||
| Insertion loss | > 2dB | Conformance | |
| EMI/RFI | Complies with 2004/108/EC | ||
| RoHS | Complies with Directive 2002/95/EC | ||
| Isolation Adjacent channel | > 30dB between 1310nm/1550nm | ||
| Pass band | 1310nm Port Range 1270-1410nm 1550nm Port Range 1470-1610nm | Ordering Information NPS0069-1401 | NI-CW2, Wave Division Multiplexer for singlemode 1310nm and 1550nm |
| TECHNICAL SPECIFICATIONS | |||
| Coarse Wavelength Division Multiplexer for single mode Optical Fiber | Max optical power | 250 mW | |
| Systems | No. of slots | 1 | |
| Conformance | |||
| Connector: | LC | RoHS | Complies with Directive 2002/95/EC |
| Wavelength: | 1310nm and 1550nm | ||
| NB : All CWDM systems require specific “tuned” laser transmitters with individual 20 nm window output wavelengths. | |||
| Insertion loss | > 2dB | ||
| Isolation Adjacent channel | > 30dB between 1310nm/1550nm | Ordering Information | |
| Pass band | 1310nm Port Range 1270-1410nm | NPS0070-14A1 | NI-CW4, 4-Channel CWDM Card |
| 1550nm Port Range 1470-1610nm | Centre Wavelengths 1510/1530/1550/1570 nm | ||
| General Card Specifications | NPS0070-14B1 | NI-CW4, 4-Channel CWDM Card | |
| Depth | 60 mm | Centre Wavelengths 1470/1490/1590/1610 nm | |
| Width | 20 mm 4TE | ||
| Height | 129 mm (3RU) | NPS0070-14C1 | NI-CW4, 4-Channel CWDM Card |
| Weight Operating Temp | 100 g 0 to +70°C | NPS0070-14D1 | Centre Wavelength1270/1290/1310/1330nm NI-CW4, 4-Channel CWDM CardCentre Wavelengths 1350/1370/1390/1410 nm |
| TECHNICAL SPECIFICATIONS | |||
| Coarse Wavelength Division Multiplexer for single mode Optical Fiber Systems | General Card Specifications | ||
| Depth | 60 mm | ||
| Connector: | LC | Width | 20 mm 4TE |
| Channels | 8, additional channels via multiple | Height | 129 mm (3RU) |
| NI-CW4 or NI-CW8 | Weight | 100 g | |
| Center wavelengths (nm) | 1270/1290/1310/1330/ 1350/1370/1390/1410 or 1470/1490/1510/1530/ 1550/1570/1590/1610 | Max optical power 250 mW | |
| Optical bandwidth | > 13 nm | No. of slots | 1 |
| Insertion loss | < 1.9 dB | ||
| Link loss for mux/demux pair | < 3.8 dB | Conformance | |
| Isolation Adjacent channel | > 30 dB | RoHS | Complies with Directive 2002/95/EC |
| Non-adjacent channel | > 40 dB | NB : All CWDM systems require specific “tuned” laser transmitters with individual 20 nm window output wavelengths. | |
| Isolation spectral range | 1260-1620 nm | ||
| Return Loss | > 45 dB (50 dB typ.) | ||
| Directivity | > 50 dB | ||
| Polarization dependent loss | < 0.2 dB | Ordering Inspiration | |
| NPS0071-14A1 | NI-CW8, 8-Channel CWDM Card Centre Wave-lengths 1270/1290/1310/1330/1350/1370/1390/1410 nm | ||
| NPS0071-14B1 | NI-CW8, 8-Channel CWDM Card Centre Wave- lengths 1470/1490/1510/1530/1550/1570/1590/ 1610 nm | ||
| TECHNICAL SPECIFICATIONS | |||
| NI-102 | Conformance | ||
| Network Monitoring Card with Ethernet 10Base-T connection for Slot-16. | |||
| NI-102 can only be fitted in a Nimbra 143 V2 or Nimbra 141 V2 frame | EMI/RFI | Complies with 2004/108/EC | |
| Optional – 1 required per frame | Electrical | Complies with EN 61000-6-1, EN 61000-6-2 | |
| RoHS | Complies with Directive 2002/95/EC | ||
| General frame specifications | |||
| Depth: | 250 mm | Ordering information | |
| Width: | 445mm | NPQ0019-AW01 | Nimbra 143 (AC) |
| Height: | 132.5 mm (3RU) | 19” 3RU Chassis for up to 15 MMS | |
| OWpeiegrahtti:ng Temp: | -113 0k gt ow +h7e0n° fCully loaded | Cards with optional Network Monitoring and including Dual Redundant Power Supplies | |
| Voltage Range: | 90 to 250 VAC 47 to 663 Hz | ||
| Power: | 65 W when fully loaded | ||
| Signal detect:No of slots: | Contact closure for psu failure15 Traffic modules slots 1 Network monitor slot | NPS0078-1401 | NI-102Network Monitoring Card with Ethernet connection. Can only be fitted in V2 chassis. |
| TECHNICAL SPECIFICATIONS | |
| API’S | HTTP based API for – Service creation – Node status – Network and link status – Service status |
| Architecture | Single or redundant – Controllers – API end-points – Paths to network elements |
| Pre-integrations | Network Management – Nimbra Vision Scheduling – ScheduALL LINK Workflow orchestration – ScheduALL Media Billing – ScheduALL |
| TECHNICAL SPECIFICATIONS | |||
| Nimbra Vision Clients | NPK0003-RS02 | Nimbra Vision Redundant Server License | |
| Operating System | Windows Server 2008 R2, Windows Server 2012 R2, Windows 7, Windows 8, Windows 10 | NPM0003-DS01 | Nimbra Vision SDN Controller Frontend License |
| Browser | Internet Explorer, Chrome, Firefox, Safari | NPM0004-0001 | Nimbra Vision Installation and Documentation CD |
| Hardware | Minimum 733MHz Pentium III, 256MB RAM, 200MB disk | NPM0003-SU01 | Nimbra Vision Upgrade License |
| NPM0003-PIN1 | Nimbra Vision Northbound Provisioning Interface License | ||
| Java Web start Client | NPM0056-0001 | Nimbra Vision Web Client Feature License | |
| Browser | Internet Explorer 7.0 or later, Firefox 2.0 or later, Chrome, Safari | NPM0057-0001 | Nimbra Vision Performance Monitoring Feature License |
| Browser plug-in | Java 8 | NPM0058-0001 | Nimbra Vision Visualization Feature License |
| Java | Java 8 | NPK0035-0001 | Nimbra Vision CPN Bundle |
| Java web start | Java 8 | NPK0036-0001 | Nimbra Vision NMS Provisioning Bundle |
| Node Licenses | |||
| HTML Client | |||
| Browser | Internet Explorer 10-11, Edge, Chrome, Firefox, Safari | NPM0003-C301 | Nimbra Vision Node License, Nimbra 300 |
| NPM0003-C601 | Nimbra Vision Node License, Nimbra 68x | ||
| Nimbra Vision Server | NPM0003-C641 | Nimbra Vision Node License, Nimbra 640 | |
| Operating System | Windows Server 2008 R2, Windows Server 2012 R2, Windows 7, Windows 8, Windows 10 | NPM0003-NM01 | Nimbra Vision Node License, Nimbra Media GW |
| NPM0003-C130 | Nimbra Vision Node License, Nimbra 130 | ||
| Ordering Information | NPM0003-C140 | Nimbra Vision Node License, Nimbra 140 | |
| NPK0003-S002 | Nimbra Vision SDN Controller | NPM0003-C230 | Nimbra Vision Node License, Nimbra 230 |
| NPM0003-SP01 | Nimbra Vision Service Provisioning License | NPM0003-VA01 | Nimbra Vision Node License, Nimbra VA |
| NPM0003-HP01 | Nimbra Vision Headend Protection License | NPM0003-OT01 | Nimbra Vision Node License, Nimbra OT 100 |
| NPM0003-PRE1 | Nimbra Vision Pre-emption License | NPM0003-3P01 | Nimbra Vision Node License, 3rd party node |
| TECHNICAL SPECIFICATIONS | ||
| Supported Nimbra products: | ||
| Architecture: | Single or redundant instance | |
| Nimbra 600 series | ||
| Nimbra 300 series | Ordering Information: | |
| Nimbra VA 220 | TP-TS0101 | Touch&Switch starter package incl 1 instance and 16 serviceports |
| TP-TS0011 | Touch&Switch extra instance | |
| Supported Access: | TP-TS0012 | Touch&Switch extra instance for redundancy |
| 8 x Video Access | TP-TS0022 | Touch&Switch extra port for redundancy |
| Ethernet Access | TP-TS0023 | Touch&Switch per port 17- 29 ports |
| AES/EBU Access | TP-TS0024 | Touch&Switch per port 30-49 ports |
| MPEG4 Access | TP-TS0025 | Touch&Switch per port 50-99 ports |
| JPEG2000 Video Access | TP-TS0026 | Touch&Switch per port 100-199 ports |
| TP-TS0027 | Touch&Switch per port 200-349 ports | |
| TP-TS0028 | Touch&Switch per port over 350 ports | |
| Standards compliance: | TP-TS0050 | Touch&Switch maintenance fee |
| SNMP v2c/v3 | ||
| Touch & Switch application: Operating System: Windows XP, 7, 8, Server 2008 Hardware: 32/64bit, 2GB RAM, 1GHz CPU | ||
Related Resources
White Paper
Cloud Ingest of Live Video
As cloud production becomes an integral part of broadcasters’ live workflows, the corresponding cloud infrastructure becomes an integral part of the media transport network.
Case Study
World’s largest Nimbra networks to HD
Since 2004, when the EBU selected Net Insight’s Nimbra platform, the EUROVISION Fibre Network (FiNE) has evolved with Net Insight’s latest products and features.
Blog
Key Industry Trends at NAB 2019
What we saw at NAB 2019 was the continuation of some of the trends in 2018, with the emergence of new developments.
